Please select your home edition
Edition
SWC newsletters (top)

Top Tips For Summertime Sessions!

by Ben Harden, Allen 12 Aug 2020 06:36 UTC
49er sailors Chris and Rhos training in Weymouth © Dylan Fletcher

Summer's in full swing in the UK with some parts of the country hitting a whopping 36C recently. So, it's no surprise then that many are leaping at the chance to get on the water! The team at Allen has a couple of top tips to consider when heading out in the heat!

UV Damage - Not only your skin but also rope, hardware and foils. It is vitally important to lather on the sun cream before heading out on the water, but it's just as important to perform regular checks on hardware and rope that may be left out in the elements all year round. UV deteriorates most materials, including nylon, which is utilised in many Allen products. The plastic parts of the blocks and cleats may start to appear faded and they will start to become brittle if left to succumb to UV over long periods. The same goes for rope, it may start to appear faded and will lose strength as the fibre's breakdown in the UV. It's important to keep an eye on these fittings to avoid failures when on the water. You may also want to consider keeping your centreboard and rudder out of direct sunlight for long periods, as heat can cause some materials to warp and twist out of shape.

Fresh Water - Keeping hydrated in the heat is a key factor in maintaining performance when sailing, but, freshwater also extends the performance and life of your kit. If you sail in salty water, it's important to always wash your boat and hardware off after each session. When seawater evaporates it leaves behind the salt crystals which can clog and even jam some bits of kit. If left to dry and not washed out, the salt will act in the same way as sand if it gets into your blocks and cleats, slowly wearing away the internal mechanisms reducing the performance and longevity of the product.

Bung removal - When storing a dinghy in the heat always remove the drainage bung or hatch covers to allow air circulation. Not only will this help keep your hull dry, but it will also stop the boat from popping. As the air inside the hull expands in the heat it will find a way to escape, usually through deck fittings, meaning that your dinghy is more likely to have small leaks when on the water. It is also important that you have a breather hole (usually a small hole in the hatch cover) to allow air to be sucked in or out. This is important when going from the land on a hot day to launching the dinghy into cold water. The air inside the boat will compact and, in some cases, could cause foredecks to concave under the pressure, weakening the integrity of the hull.

For more tips, rigging guides or general sailing news head over to www.allenbrothers.co.uk where you will also find the full range of Allen hardware available to purchase directly online. All Allen hardware is made in Essex, UK.

#equippedwithallen #madeintheUK

Related Articles

Allen Through Deck Block Range Expands
Now includes stainless steel sheaves and recycled acetal sheaves We are pleased to announce that our range of 20mm & 30mm through deck blocks is expanding to include stainless steel sheaves and recycled acetal sheaves. Posted on 3 Jun
New range of flanged aluminium deck bushes
Four sizes and six colours available from Allen The new range of flanged aluminium deck bushes is now available. Allen flanged aluminium deck bushes feature a wider surface area with two fixing holes, allowing for a simple installation which only requires two screws and no mess. Posted on 13 May
Pump it up! Allen's mainsheet roller fairlead
Designed to remove friction and give you back control of the rope Pump it up with the mainsheet roller fairlead. Designed to remove friction and give you back control of the rope. Posted on 22 Apr
Allen Wave Ratchet: More Grip - Less Slip
20 to 40% more grip without adding any additional wear to the rope The Wave Ratchet offers between 20 to 40% more grip without adding any additional wear to the rope. Posted on 16 Apr
Sail Slides & Slugs - How to choose correctly
Not the most exciting piece of equipment, but they are a very useful bit of kit Sail slides and slugs may not be the most exciting piece of equipment found on a sailboat. However, they are a very useful bit of kit and can make your life on board a vessel much easier. Posted on 29 Mar
Allen Product Feature - Pad-Tii
A great choice if you are looking to add an attachment point to a surface Pad-Tii's are a great choice if you are looking to add an attachment point to a surface. They offer minimal protrusion yet are easy to thread rope around and give a strong, solid fixing point for any fitting. Posted on 22 Mar
Allen Product Feature: Deck Bushes & Snatch Blocks
Two extremely useful types of fitting for your boat A through deck bush is designed to protect a surface from a rubbing rope or wire, they can also be used to act as a deflecting point. A snatch block is a variation of pulley that has been designed to allow quick attaching and releasing of lines. Posted on 2 Mar
Allen renewed as official hardware supplier
To the Swedish Sailing Team The Swedish Sailing Team has confirmed Allen as their official hardware supplier for another year. Posted on 29 Jan
The Big Boy - Allen's Biggest Block Yet!
Just one example of what Allen can do for bigger boats Around the world, we are known as a company that produces small boat hardware, but this isn't strictly true. Let us introduce to you to "The Big Boy" just one example of what we can do for bigger boats. Posted on 22 Jan
Jon Sturmer joins Allen
Appointed as Business Development Manager at the UK performance hardware manufacturer UK performance hardware manufacturer, Allen Brothers (fittings) Ltd, has appointed Jon Sturmer as Business Development Manager. Posted on 11 Jan
MBW newsletters (top)